# wood weight per square foot

### GE-1 Weights Building Materials - Boise Cascade Wood

Technical Note Tech Note GE-1 Page 1 of 2 r07/2016 valid 2 years past publish date Weights of Building Materials Pounds Per Square Foot PSF CEILING Acoustical fiber board 1 1 Suspended steel channel system 1 2 Suspended wood channel system 2.5

### WEIGHT OF WALL AND PARTITIONS IN - Ohio University

WEIGHT OF WALL AND PARTITIONS IN psf Material Weight Movable Steel Partitions 4 Wood or Steel Studs, 1/2" Gyp Board Each Side 8 Wood Studs, 2x4, Unplastered 4 FRAME PARTITIONS Wood Studs, 2x4, Plastered One Side 12 Material Weight Felt, per ply .5 Gravel 4 Roll Roofing 1 235 Ib Shingles and Paper 2.5 2 15 Ib and I 90 Ib 1.7

### How to Calculate Lumber Weight Our Pastimes

Southern pine weighs 34.4 pounds per 1 cubic foot, and 1 cubic foot is 1,728 cubic inches. Thus, the beam in this example measures 1.8 cubic feet, times 34.4 pounds per cubic foot, or 64.5 pounds. Tip

### Wood Species - Moisture Content and Weight

Board Feet Chart - Board feet - a volume measurement of lumber Combustion of Wood - Heat Values - Firewood and combustion of wood heat values - for species like Pine, Elm, Hickory and more Densities of Wood Species - Densities of wood species like apple, ash, cedar, elm and more

### Plywood Weight ThePlywood.com

In it, they state that softwood plywood should weigh approximately 3 pounds per square foot, per inch of thickness. Actual plywood weight is slightly less, as the specification is for pre-sanded sheets.

### Wood Species - Moisture Content and Weight

Wood Species Fresh Green Wood Air-dried Seasoned Wood 20% moisture content per weight unit Specific Gravity Density lb/ft 3 Weight per Cord lb/cord Specific Gravity Density lb/ft 3 Weight per Cord

### How to Calculate the Weight of Plywood Hunker

Engineers have rounded-off weight calculations for plywood to square foot calculations, and have decided that, for engineering purposes, a generic square foot of 3/4-inch-thick hardwood plywood weighs 2.3 pounds.A 4-by-8 sheet of plywood equals 32 square feet, so 32 times 2.3, is just over 70 pounds per sheet.

### How much does a house weigh? - JLC-Online Forums

32 feet square, 2 stories. He added on a bit for the car port and the small slab floor under a laundry floor. Works out to roughly 121 pounds per square foot of footprint, or 60 pounds per square foot total living space.

### Product Weights Hood Distribution

Product Weights Lumber and Panel Weights The two charts below provide pound-per-square foot weights for a variety of rough lumber species and structural panels including plywood, MDF, particle board and melamine.

### Approximate Weights of Wood in LBS

Approximate Weights of Wood in LBS./Cu. Ft. APPROXIMATE WEIGHTS OF WOOD IN Lbs./Cu. Ft. Species Green Airdry Alder, red 46 28 Ash, black 52 34 Ash, commercial white 48 41 Ash, Oregon 46 38 Aspen 43 26 * all values are based on oven dry weight One Full Cord = 128 cubic feet

### Seven Trust Specs

Weight. Seven Trust wood decking has specific gravity of 0.85 to 1.08. Air dried density is 66 to 75 lbs. per cubic ft. A 3/4" thick finish material weights approx. 4.5 lbs. per sq ft.

### Lumber and Wood Products Weights and Measures

Wood Products Weights and Measures. 1 FBM = 1 board foot 12" x 12" x 1" 1 MFBM = 1,000 fbm 1 MSF = 1,000 square feet veneer or panel board 1 cunit = 100 ft3 1 cord = 128 ft3 x 4' x 4' x 8' 85 ft3 solid wood, 15ft3 air, and 28ft3 of bark Roundwood Weight 1 metric tonne = m3 1 White Pine = 1.1198 m3 Red Pine = 1.1820 m3

### Average Dry Weight - Exotic Wood, Birdseye Maple, Curly

The average dry weight of each species is calculated at 8% moisture content. It is listed in pounds per cubic foot or kilograms per cubic meter. To find the average dry weight per board foot, divide the pounds per cubic foot by 12.

### APPENDIX A WEIGHTS OF BUILDING MATERIALS

APPENDIX A WEIGHTS OF BUILDING MATERIALS SECTION A101 DEAD LOAD IN POUNDS PER SQUARE FOOT COMPONENT LOAD COMPONENT LOAD CEILINGS Rigid insulation1,/ Wood furring suspension system 2.5 Wood sheathing per in. 3 Wood shingles 3 COVERINGS, ROOF AND WALL Wood structural panel pe1/r